Arduino Ethernet shield R3

Arduino Ethernet shield R3
Click image for Gallery
  • Product Code:SQ1052
  • Availability: 10000
  • $9.95
  •  
  • Ex Tax:$9.95
+
-


Tags: Arduino Ethernet Shield, Arduino Ethernet Shield W5100, arduino shield

Description:

The Arduino Ethernet Shield R3 allows an Arduino board to connect to the internet. It is based on the Wiznet W5100ethernet chip. The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.

Arduino communicates with both the W5100 and SD card using the SPI bus (through the ICSP header). This is on digital pins 10, 11, 12, and 13 on the Uno and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5100 and pin 4 for the SD card. These pins cannot be used for general I/O. On the Mega, the hardware SS pin, 53, is not used to select either the W5100 or the SD card, but it must be kept as an output or the SPI interface won't work.

Note that because the W5100 and SD card shares the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output.

The reset button on the shield resets both the W5100 and the Arduino board. The Ethernet Shield R3 has a standard RJ-45 connection, with an integrated line transformer and Power over Ethernet enabled.

There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with all the Arduino/Genuine boards. The onboard micro SD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4.

Note:
The solder jumper marked "INT" can be connected to allow the Arduino board to receive interrupt-driven notification of events from the W5100, but this is not supported by the Ethernet library. The jumper connects the INT pin of the W5100 to digital pin 2 of the Arduino.


Arduino Ethernet Shield W5100 Application:

  1. Bluetooth
  2. Arduino projects
  3. internet projects


Arduino Ethernet Shield W5100 Specifications:

  1. The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted pair Category 5 Ethernet cable:
  2. IEEE802.3af compliant
  3. Low output ripple and noise: 100mVpp
  4. Input voltage range: 36~57V
  5. Overload and short-circuit protection
  6. Output: 9v
  7. High efficiency DC/DC converter: typ 75% @ 50% load
  8. isolation (input to output): 1500V

Arduino ethernet shield pinout:

  1. PWR: indicates that the board and shield are powered
  2. LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
  3. FULL: indicates that the network connection is full duplex
  4. 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
  5. RX: flashes when the shield receives data
  6. TX: flashes when the shield sends data
  7. COLL: flashes when network collisions are detected


Documents:

  1. Arduino ethernet shield r3 datasheet Link
  2. arduino ethernet shield projects Link

Physical Parameters
Size 68.6mm X 53.3mm

Write a review

Note: HTML is not translated!
   Bad           Good
Captcha
Electronic & Robotic Supplier

Your B2B Supplying Partner in Mainland China

Worldwide Shipping

Using Vast Majority of International Couriers

Secure Payments

Always Pay with Trust by PayPal Express Checkout