PCA9685 16 Channel PWM Servo Controller Module [12 Bit] [I2C]

PCA9685 16 Channel PWM Servo Controller Module [12 Bit] [I2C]
Click image for Gallery
  • Brands CJMCU
  • Product Code:SQ2620
  • Availability: 10000
  • $6.50
  •  
  • Ex Tax:$6.50
This product has a minimum quantity of 3
+
-


Tags: Servo Motor Driver, PWM Servo Motor Controller, CJMCU PCA9685, 16 Channel PWM Servo Controller, PCA9685, FastMode Plus Family, LED Backlight Driver

Description:
CJMCU PCA9685 16 Channel PWM Servo Controller Module is a 16 Channel, PWM servo controller with a built in clock, which is based on PCA9685 chip. The PCA9685 chip is an I2C-controlled, which is optimized for Red/Green/Blue/Amber (RGBA) color backlighting devices. Each LED output has its own 12bit resolution and can be achieved from the completely closed (default) to 4096 levels (212  Levels), between the maximum brightness linear programmable brightness. The PCA9685 is in the new Fast-mode Plus (Fm+) family. Fast-mode Plus devices provides higher frequency (up to 1 MHz) and more densely populated bus operation (up to 4000 pF). The PCA9685 has some especial aspects, which make it suitable for LCD or LED backlighting and Ambilight TVs, LED displays, LCD backlights, RGB or RGBA LED drivers, LED status information and Keypad backlights for cellular phones or handheld devices.
This module is 5V compliant, so it can be supplied with a 3.3V microcontroller and even safely up to 6V supplier. It has 6 pins for addressing, so you can connect up to 62 states with a single I2C bus and get a total of 992 outputs for controlling a lot of servos or driving a lot of LEDs. Because of having an embedded in clock, it's self running and not needed to continually trigger it with signal tying up microcontroller.

​​​​Features:
Each output programmable at these 4 cases: Off, On, Programmable LED brightness, Programmable LED turn-on time to help reduce EMI
1 MHz Fast-mode Plus compatible I2C interface with 30 mA high drive capability on SDA output for driving high capacitive buses
4096-levels (12-bit) linear programmable brightness per LED output changing from fully off (default) to maximum brightness
Software programmable open-drain LED output selection (default is push-pull) of 16 push-pull outputs (5V at 25mA sink can absorb and provide 10mA Source Current), no input function
Output mode change programmable on the Acknowledge or the STOP Command to update outputs byte-by-byte or simultaneously (default to ‘Change on STOP’)
Active-low output enable input pin when the pin is high LED outputs can be programmed 0,1 or tri-state (high impedance power-on default)
6 hardware address pins so that the same I2C devices can be connected to the bus 62 PCA9685
LED output frequency range (all LEDs) typically is from 24 Hz to 1526 Hz (Default of 1Eh in PRE_SCALE register leads in a 200 Hz refresh rate with 25MHz clock pulse)
4 software programmable I2C-bus addresses (one LED All Call address and three LED Sub Call addresses) allow some group of devices to be addressed simultaneously in any combination (for example, one register used for ‘All Call’ so that all the PCA9685s on the I2C-bus can be addressed together in a time and the second register used for three different addresses so that 1⁄ 3 of all devices on the bus can be addressed simultaneously in a group). Software enable and disable for the I2C-bus address.
Software reset feature (SWRST) makes the device via the I2C bus resets
25MHz internal oscillator requires no external components
External 50 MHz (max.) clock input
Supports hot insertion
An internal power-on reset
Using a noise filter on the SDA / SCL inputs  
Edge rate control on outputs
No output glitches on power-up
ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101
Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
Hot-Access
Low Standby Current 
PWM Frequency: 24Hz ~ 1526Hz
PWM Duty Cycle: 0 % ~ 100 %
Interface: I2C
Temperature: -40°C ~ +85°C
Size: 65mm x 30mm

Package Include:
1 x PCA9685 16 Channel PWM Servo Control Module
1 x Terminal
6 x Pin Header

Interfaces
Interface Type I2C
Electrical Parameters
Operating Voltage 2.3V ~ 5.5V
Board Parameters
PWM Duty Cycle 0 % ~ 100 %
PWM Frequency 24Hz ~ 1526Hz
Physical Parameters
Operating Temperature -40°C ~ +85°C
Size 65mm x 30mm

Write a review

Note: HTML is not translated!
   Bad           Good
Captcha
Electronic & Robotic Supplier

Your B2B Supplying Partner in Mainland China

Worldwide Shipping

Using Vast Majority of International Couriers

Secure Payments

Always Pay with Trust by PayPal Express Checkout