433MHz Remote Controller

Note: This remote is Copyable or Can be duplicated.

433MHz Copy Remote Control is a four-channel 433 MHz pen remote with a beautiful design and compact dimensions. The battery used in this remote is a 12V 27A type. The small size and practical design of this remote are excellent, and it can be used in many projects. This 433 MHz remote is made of plastic and metal, has a transmission power of 100 milliwatts, and a range of approximately 50 to 100 meters.

New fast copy type remote control product description

1. Chips that can be copied:

 2260 (all manufacturers), 2262 (all manufacturers), PT2264, 5326 (all manufacturers), SC5262, HT600, HT680, HT6207, HT6010, HT6012, HT6014, SMC918 series, 527 (all manufacturers), 1527 (all manufacturers), 2240 (all manufacturers), HCS101, HCS200/HCS201 (partial code), HCS300/HCS301 (partial code), some microcontrollers...

1. Chips could be copied

2260(all manufacturers);2262(All manufacturers);PT2264, 5326(All manufacturers);SC5262, HT600, HT680, HT6207, HT6010, HT6012, HT6014, SMC918series,527(All manufacturers);1527(All manufacturers);2240(All manufacturers);HCS101, HCS200\HCS201(part code),HCS300\HCS301(part code), part single chip microcomputer.....

2. Clear code method:

 Press and hold the lock and unlock buttons simultaneously (some casings have up and down buttons). The LED indicator will flash three times. Release either button you pressed, but keep holding the other button. Press the released button three times. The LED indicator will then start flashing rapidly. At this point, all data in the memory will be cleared. After the data is cleared, the LED indicator will not light up no matter which button you press on the remote control.

3. Code cleaning method:

Press the unlock button and lock button at the same time (some shells are the up button and down button), after the LED indicator light flashes three times, loosen any one of the buttons while the other is kept pressing, then push the released button three times, the LED indicator will enter into the fast flashing status. At this time all the memory data is cleared, the cleaned remote control will not have lighting LED indicator no matter which button you press.

4. Copying method:

Hold the original remote control in one hand and the copy remote control in the other. Keep both remote controls as close together as possible (ideally, place them side-by-side on a table with almost no distance between them). Press the desired copy button on each remote control. The LED indicator will flash three times quickly, then flash rapidly again, indicating successful copying. Repeat the same process for other buttons. Some remote controls have lower transmission power; in these cases, the original and copy remote controls should be placed back-to-back for better copying results. Avoid environments with interference. If copying is unsuccessful, clear the code and try again. (Very Important: Your remote control must be working properly and operate on the same frequency as our remote control.)

5. Copy method

One hand keeps the original remote controller, while another keeps the copy remote control, the two remote controls should be placed as closely as possible (the ideal situation is to put the two remote controls on the desktop side by side with zero distance), respectively press down the copy button, when the LED indicator light flashes quickly after three flashes, this copy is successful, other key operating methods are the same. Some remote control has a smaller transmitting power, so the original remote control should be placed back to the copy remote control to be operated. For the presence of noise, it should avoid interference to operate, If the copy is not successful, it should recopy after clearing code. 

Note: Your original remote control must be able to work and the same as our remote control frequency

6. Features of the new copying remote control:

The four buttons can copy four different types of chips, meaning one remote control can operate four different types of devices. Data copying is fast, with low risk of code loss, and has a long range.

7. The features of new copy remote control

The four buttons could respectively copy four different types of chips, That is a remote control can operate four different types of facilities. T Faster copy data speed, not easy losing code, far distance.

4 channel Remote application:

1. Garage Doors
2. Entry and Exit Gates
3. Roll-Up Gates / Rolling Gates
4. Home Security Systems
5. Industrial Control Products

433MHz Copy Remote Control specification:

1. Weight: 20 grams
2. Material: Plastic and Metal
3. Operating Voltage: 12V DC
4. Operating Current: 8 mA
5. Operating Frequency: 433 MHz
6. Transmission Power: 100 mW
7. Transmission Distance: 50 to 100 meters
8. Operating Temperature: -10°C to 50°C
9. Copyable / Can be duplicated